mizar32 Lua board on sale
Locked
12
12
|
Hi
The Mizar32 board, the first commercial computer to come with Lua (eLua) as its operating system, is now on sale at 4star.it Specs: 66Mhz AVR32 CPU, 32MB RAM, I2C, SPI, PWM, ADC, SD-card, USB with UART, Ethernet, character LCD and VGA add-on modules. Web: http://simplemachines.it/mizar32 Shop: http://4star.it -> mizar32 best M _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Congratulations! Nice work.
Best, Bogdan On Wed, May 2, 2012 at 1:36 AM, Martin Guy <[hidden email]> wrote: > Hi > The Mizar32 board, the first commercial computer to come with Lua > (eLua) as its operating system, is now on sale at 4star.it > > Specs: 66Mhz AVR32 CPU, 32MB RAM, I2C, SPI, PWM, ADC, SD-card, USB > with UART, Ethernet, character LCD and VGA add-on modules. > > Web: http://simplemachines.it/mizar32 > Shop: http://4star.it -> mizar32 > > best > > M eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
In reply to this post by Martin Guy
Hi,
Nice board and it's good to see more eLua hardware and add-ons becoming available. Though not necessarily the very first commercial computer running eLua - as Omnima has been shipping eLua on the STM32Expander add-on board for MiniEMBWiFi Linux solution for a few months now :) Regards, Ivan Omnima Limited Ivan Ignjatic Oxford Business Centre Osney Mead Oxford OX2 0DR Tel. 0845 8692601 Fax. 01865 326421 Web: www.omnima.co.uk Skype: omnimaautomation On 01/05/2012 23:36, Martin Guy wrote: Hi The Mizar32 board, the first commercial computer to come with Lua (eLua) as its operating system, is now on sale at 4star.it Specs: 66Mhz AVR32 CPU, 32MB RAM, I2C, SPI, PWM, ADC, SD-card, USB with UART, Ethernet, character LCD and VGA add-on modules. Web: http://simplemachines.it/mizar32 Shop: http://4star.it -> mizar32 best M _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Hi, Martin, great to see eLua based product on the shelf, especially with complete set of add-on modules. Ivan, there is no mention of eLua on the STM32Expander product page or in its documentation pdf - fix it! ;)
Kamil On Wed, May 2, 2012 at 9:54 AM, Ivan - Omnima <[hidden email]> wrote:
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Hi Kamil,
The details about STM32Expander and eLua are published on the Omnima forum: http://www.omnima.co.uk/forums/index.php?showtopic=209 Regards, Ivan Omnima Limited Ivan Ignjatic Oxford Business Centre Osney Mead Oxford OX2 0DR Tel. 0845 8692601 Fax. 01865 326421 Web: www.omnima.co.uk Skype: omnimaautomation On 02/05/2012 09:36, Kamil Zadora wrote:
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
In reply to this post by Martin Guy
Hello Martin, Excellent work! Congrats. Cheers, Raman |
|
|
In reply to this post by Martin Guy
Is there any short-range wireless modules available (bluetooth, zigbee)?
Geir kl. 00:36:56 UTC+2 onsdag 2. mai 2012 skrev martinwguy følgende: Hi _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Take a look at what Digi can offer and Wi-Fly from Roving Networks.
There are combo modules available that do Blue tooth and Wi-Fi.
Q.
Is there any short-range wireless modules available (blue tooth, Zigbee)?
Geir
kl. 00:36:56 UTC+2 onsdag 2. mai 2012 skrev martinwguy følgende:Hi The Mizar32 board, the first commercial computer to come with Lua (eLua) as its operating system, is now on sale at 4star.it Specs: 66Mhz AVR32 CPU, 32MB RAM, I2C, SPI, PWM, ADC, SD-card, USB with UART, Ethernet, character LCD and VGA add-on modules. Web: http://simplemachines.it/mizar32 Shop: http://4star.it -> mizar32 best M _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
 
|
Sergio Sorrenti |
Re: mizar32 Lua board on sale
|
|
In reply to this post by gmkoien
Hi Geir,
we have a Kicad design (schematic, pcb file and gerbers) of an Xbee adaptor for Mizar32, + some available sample, unfortunately this is untested. We will pubblish them today on our gcode download repository, here . Regarding the BT, one of our member, Nuccio, is experimenting with some cheap and widespread BT modules with standard interfaces. I will ask him to post some informations on this thread. Sergio Il giorno martedì 27 novembre 2012 13:21:41 UTC+1, [hidden email] ha scritto: Is there any short-range wireless modules available (bluetooth, zigbee)? _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
In reply to this post by gmkoien
Hi Geir,
I got excellent results using this cheap module: http://www.rasmicro.com/Bluetooth/EGBT-045MS-046S%20Bluetooth%20Module%20Manual%20rev%201r0.pdf http://www.rasmicro.com/Bluetooth.htm http://club.dx.com/forums/forums.dx/threadid.1052121 It acts as a standard UART (so you can connect it on Mizar serial port) and costs few dollars (about 10$). I hope it helps. Nuccio Il 27/11/2012 13:21, [hidden email] ha scritto: > Is there any short-range wireless modules available (bluetooth, zigbee)? > > Geir > > kl. 00:36:56 UTC+2 onsdag 2. mai 2012 skrev martinwguy følgende: > > Hi > The Mizar32 board, the first commercial computer to come with Lua > (eLua) as its operating system, is now on sale at 4star.it > <http://4star.it> > > Specs: 66Mhz AVR32 CPU, 32MB RAM, I2C, SPI, PWM, ADC, SD-card, USB > with UART, Ethernet, character LCD and VGA add-on modules. > > Web: http://simplemachines.it/mizar32 > <http://simplemachines.it/mizar32> > Shop: http://4star.it -> mizar32 > > best > > M > _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Hello All
If I was to design an Ethernet to serial gateway would there be any interest? Basically it would accept 10/100 Mb Ethernet and convert it to serial or SPI and vica-versa.
I would make all the gerber files available. I think that a modular method is perhaps the best route to follow as main processor is then not burdened with these other tasks. All it has to do is to capture packets on the Serial or SPI layer, process them and reply if necessary.
I also have a complete design for a small PLC using the STR912FAW47. It has:
Most of the low level drivers are written in C and have been battled tested. This is revision 2 of the board, so there are a few hardware changes and some of the drivers have to change, or still have to be written. Everything is interrupt driven.
I have not yet had the time to implement eLua on it, but there is a port available for this CPU.
Is anyone interested in working with me to get this up and going with eLua?
Quentin
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
I would be interested and willing to help you get eLua running on your PLC board. I am unlikely to have much time for the next two weeks due to a work project deliverable. After that I could spend some time on getting eLua running and working on some modules to interface to the various hardware peripherals.
I also may be interested in your Ethernet gateway board, as I have a few projects where I plan on using eLua and will need Ethernet. -djd On Nov 28, 2012, at 11:58 PM, Quentin Barry wrote:
-- Douglas Davenport _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
That would be great. I also have quite a hectic schedule for approximately the next 2 weeks and then I will be free. Being your own boss can kill you sometimes.
I have all the PDF files for the PLC - where can I deposit them? If people are happy with what they see then I will upload all the Gerber files a bit later. All I need is a bit of guidance here on where to deposit the files without creating confusion. I guess a bit of moderator support is required at this junction.
Quentin.
I would be interested and willing to help you get eLua running on your PLC board. I am unlikely to have much time for the next two weeks due to a work project deliverable. After that I could spend some time on getting eLua running and working on some modules to interface to the various hardware peripherals.
I also may be interested in your Ethernet gateway board, as I have a few projects where I plan on using eLua and will need Ethernet.
-djd
On Nov 28, 2012, at 11:58 PM, Quentin Barry wrote:
Hello All
If I was to design an Ethernet to serial gateway would there be any interest? Basically it would accept 10/100 Mb Ethernet and convert it to serial or SPI and vica-versa.
I would make all the gerber files available. I think that a modular method is perhaps the best route to follow as main processor is then not burdened with these other tasks. All it has to do is to capture packets on the Serial or SPI layer, process them and reply if necessary.
I also have a complete design for a small PLC using the STR912FAW47. It has:
Most of the low level drivers are written in C and have been battled tested. This is revision 2 of the board, so there are a few hardware changes and some of the drivers have to change, or still have to be written. Everything is interrupt driven.
I have not yet had the time to implement eLua on it, but there is a port available for this CPU.
Is anyone interested in working with me to get this up and going with eLua?
Quentin_______________________________________________
eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev --
Douglas Davenport
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Take a look at:
On Thu, Nov 29, 2012 at 7:53 AM, Quentin Barry <[hidden email]> wrote:
Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private infrastructure" Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Quentin Barry |
Re: [SPAM] Re: ARM9 Embedded PLC
|
|
Thanks for the link.
The issue here is that I am a hardware / embedded engineer. I don't want to buy someone else's solution - but want to design my own. You may call it re-inventing the wheel, but that is OK. I am planning on using one of the Luminary Micro / Stellaris Cortex M3 devices to implement the Ethernet to Serial bridge. I could simply have used a Tibbo module if I was so inclined.
I have taken a look at the Microchip offerings but then you are tied in to their compiler and development environment. With the Stellaris solution everything is open source. One also has the flexibility to change and add things as well. For example I could add a CC1125 to the Cortex as well and then I would have an Ethernet and an ISM band device in one.
Quentin
Take a look at:
On Thu, Nov 29, 2012 at 7:53 AM, Quentin Barry <[hidden email]> wrote:
That would be great. I also have quite a hectic schedule for approximately the next 2 weeks and then I will be free. Being your own boss can kill you sometimes.
I have all the PDF files for the PLC - where can I deposit them? If people are happy with what they see then I will upload all the Gerber files a bit later. All I need is a bit of guidance here on where to deposit the files without creating confusion. I guess a bit of moderator support is required at this junction.
Quentin.
I would be interested and willing to help you get eLua running on your PLC board. I am unlikely to have much time for the next two weeks due to a work project deliverable. After that I could spend some time on getting eLua running and working on some modules to interface to the various hardware peripherals.
I also may be interested in your Ethernet gateway board, as I have a few projects where I plan on using eLua and will need Ethernet.
-djd
On Nov 28, 2012, at 11:58 PM, Quentin Barry wrote:
Hello All
If I was to design an Ethernet to serial gateway would there be any interest? Basically it would accept 10/100 Mb Ethernet and convert it to serial or SPI and vica-versa.
I would make all the gerber files available. I think that a modular method is perhaps the best route to follow as main processor is then not burdened with these other tasks. All it has to do is to capture packets on the Serial or SPI layer, process them and reply if necessary.
I also have a complete design for a small PLC using the STR912FAW47. It has:
Most of the low level drivers are written in C and have been battled tested. This is revision 2 of the board, so there are a few hardware changes and some of the drivers have to change, or still have to be written. Everything is interrupt driven.
I have not yet had the time to implement eLua on it, but there is a port available for this CPU.
Is anyone interested in working with me to get this up and going with eLua?
Quentin_______________________________________________
eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev --
Douglas Davenport
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev -- Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private
infrastructure"
Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
That's OK, Quentin.
A new look at an existing product line is always welcomed. Being that you are a hardware person, take a look at the W7200 in the Wiznet site. Notice that it uses STM32 IP with 128K Flash and 20K RAM. If you can come up with the equivalent using Stellaris IP with 512 K Flash (or better) and 64K RAM (or better), I can use that. On Sun, Dec 2, 2012 at 1:26 AM, Quentin Barry <[hidden email]> wrote:
Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private infrastructure" Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Hi Tom
I was thinking of using the LM3S6965. I think that it has ample resources to suit my requirements.
It comes with 64 KB of bit-banded SRAM and 256 KB of flash memory. It has the MAC and PHY built into the IC. All that one requires is the RJ45 connector. I think that this device was targeted for Ethernet to Serial bridges. There are detailed design and application notes on their website.
Without a doubt one cannot deny that ST has the lion's share of the Cortex market. I do use their devices regularly too. However there are certain niche markets that other vendors target.
Stellaris with their LM3S6965 for Ethernet
NXP and Energy Micro for Graphics Displays - EmWin is a free download for these devices.
Si-Labs have a highly configurable patented dual crossbar technology to define pinouts.
I guess it all boils down to what the end application is.
Regards
Quentin
That's OK, Quentin.
A new look at an existing product line is always welcomed.
Being that you are a hardware person, take a look at the W7200 in the Wiznet site.
Notice that it uses STM32 IP with 128K Flash and 20K RAM. If you can come up with the equivalent using Stellaris IP with 512 K Flash (or better) and 64K RAM (or better), I can use that.
On Sun, Dec 2, 2012 at 1:26 AM, Quentin Barry <[hidden email]> wrote:
Thanks for the link.
The issue here is that I am a hardware / embedded engineer. I don't want to buy someone else's solution - but want to design my own. You may call it re-inventing the wheel, but that is OK. I am planning on using one of the Luminary Micro / Stellaris Cortex M3 devices to implement the Ethernet to Serial bridge. I could simply have used a Tibbo module if I was so inclined.
I have taken a look at the Microchip offerings but then you are tied in to their compiler and development environment. With the Stellaris solution everything is open source. One also has the flexibility to change and add things as well. For example I could add a CC1125 to the Cortex as well and then I would have an Ethernet and an ISM band device in one.
Quentin
Take a look at:
On Thu, Nov 29, 2012 at 7:53 AM, Quentin Barry <[hidden email]> wrote:
That would be great. I also have quite a hectic schedule for approximately the next 2 weeks and then I will be free. Being your own boss can kill you sometimes.
I have all the PDF files for the PLC - where can I deposit them? If people are happy with what they see then I will upload all the Gerber files a bit later. All I need is a bit of guidance here on where to deposit the files without creating confusion. I guess a bit of moderator support is required at this junction.
Quentin.
I would be interested and willing to help you get eLua running on your PLC board. I am unlikely to have much time for the next two weeks due to a work project deliverable. After that I could spend some time on getting eLua running and working on some modules to interface to the various hardware peripherals.
I also may be interested in your Ethernet gateway board, as I have a few projects where I plan on using eLua and will need Ethernet.
-djd
On Nov 28, 2012, at 11:58 PM, Quentin Barry wrote:
Hello All
If I was to design an Ethernet to serial gateway would there be any interest? Basically it would accept 10/100 Mb Ethernet and convert it to serial or SPI and vica-versa.
I would make all the gerber files available. I think that a modular method is perhaps the best route to follow as main processor is then not burdened with these other tasks. All it has to do is to capture packets on the Serial or SPI layer, process them and reply if necessary.
I also have a complete design for a small PLC using the STR912FAW47. It has:
Most of the low level drivers are written in C and have been battled tested. This is revision 2 of the board, so there are a few hardware changes and some of the drivers have to change, or still have to be written. Everything is interrupt driven.
I have not yet had the time to implement eLua on it, but there is a port available for this CPU.
Is anyone interested in working with me to get this up and going with eLua?
Quentin_______________________________________________
eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev --
Douglas Davenport
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev -- Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private
infrastructure"
Voice -<A href="tel:860-232-1614"> 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev -- Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private
infrastructure"
Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Can't go into the application. But, you are 256K Flash shy of what I need at a minimum. I don't need a display. The app runs headless.
I know the Stellaris series goes up to 1MB Flash. I need to run eLua + some other stuff
Nevertheless, keep us posted on where you are going. On Sun, Dec 2, 2012 at 10:50 AM, Quentin Barry <[hidden email]> wrote:
Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private infrastructure" Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
In reply to this post by Quentin Barry
Here is a low cost board... JeroenDS made amazing PLC project with iMX233-OLinuXino: http://leachy.homeip.net/olinuxino/ From: Quentin Barry <[hidden email]> To: eLua Users and Development List (www.eluaproject.net) <[hidden email]> Sent: Sunday, December 2, 2012 9:50 AM Subject: [eLua-dev] ARM9 Embedded PLC Hi Tom
I was thinking of using the LM3S6965. I think that it has ample resources to suit my requirements.
It comes with 64 KB of bit-banded SRAM and 256 KB of flash memory. It has the MAC and PHY built into the IC. All that one requires is the RJ45 connector. I think that this device was targeted for Ethernet to Serial bridges. There are detailed design and application notes on their website.
Without a doubt one cannot deny that ST has the lion's share of the Cortex market. I do use their devices regularly too. However there are certain niche markets that other vendors target.
Stellaris with their LM3S6965 for Ethernet
NXP and Energy Micro for Graphics Displays - EmWin is a free download for these devices.
Si-Labs have a highly configurable patented dual crossbar technology to define pinouts.
I guess it all boils down to what the end application is.
Regards
Quentin
That's OK, Quentin.
A new look at an existing product line is always welcomed.
Being that you are a hardware person, take a look at the W7200 in the Wiznet site.
Notice that it uses STM32 IP with 128K Flash and 20K RAM. If you can come up with the equivalent using Stellaris IP with 512 K Flash (or better) and 64K RAM (or better), I can use that.
On Sun, Dec 2, 2012 at 1:26 AM, Quentin Barry <[hidden email]> wrote:
Thanks for the link.
The issue here is that I am a hardware / embedded engineer. I don't want to buy someone else's solution - but want to design my own. You may call it re-inventing the wheel, but that is OK. I am planning on using one of the Luminary Micro / Stellaris Cortex M3 devices to implement the Ethernet to Serial bridge. I could simply have used a Tibbo module if I was so inclined.
I have taken a look at the Microchip offerings but then you are tied in to their compiler and development environment. With the Stellaris solution everything is open source. One also has the flexibility to change and add things as well. For example I could add a CC1125 to the Cortex as well and then I would have an Ethernet and an ISM band device in one.
Quentin
Take a look at:
http://www.wiznet.co.kr/Sub_Modules/en/
On Thu, Nov 29, 2012 at 7:53 AM, Quentin Barry <[hidden email]> wrote:
That would be great. I also have quite a hectic schedule for approximately the next 2 weeks and then I will be free. Being your own boss can kill you sometimes.
I have all the PDF files for the PLC - where can I deposit them? If people are happy with what they see then I will upload all the Gerber files a bit later. All I need is a bit of guidance here on where to deposit the files without creating confusion. I guess a bit of moderator support is required at this junction.
Quentin.
I would be interested and willing to help you get eLua running on your PLC board. I am unlikely to have much time for the next two weeks due to a work project deliverable. After that I could spend some time on getting eLua running and working on some modules to interface to the various hardware peripherals.
I also may be interested in your Ethernet gateway board, as I have a few projects where I plan on using eLua and will need Ethernet.
-djd
On Nov 28, 2012, at 11:58 PM, Quentin Barry wrote:
Hello All
If I was to design an Ethernet to serial gateway would there be any interest? Basically it would accept 10/100 Mb Ethernet and convert it to serial or SPI and vica-versa.
I would make all the gerber files available. I think that a modular method is perhaps the best route to follow as main processor is then not burdened with these other tasks. All it has to do is to capture packets on the Serial or SPI layer, process them and reply if necessary.
I also have a complete design for a small PLC using the STR912FAW47. It has:
Most of the low level drivers are written in C and have been battled tested. This is revision 2 of the board, so there are a few hardware changes and some of the drivers have to change, or still have to be written. Everything is interrupt driven.
I have not yet had the time to implement eLua on it, but there is a port available for this CPU.
Is anyone interested in working with me to get this up and going with eLua?
Quentin_______________________________________________
eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev --
Douglas Davenport
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev -- Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private
infrastructure"
Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev -- Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private
infrastructure"
Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
|
|
Quentin Barry |
Re: [SPAM] Re: ARM9 Embedded PLC
|
|
Hello Tim
Very interesting - the Classic Ladder bit.
I have a substantial implementation of the Modbus RTU protocol on my ARM9 board.
Thanks for the link.
Quentin
Here is a low cost board...
JeroenDS made amazing PLC project with iMX233-OLinuXino: http://leachy.homeip.net/olinuxino/
From: Quentin Barry <[hidden email]> To: eLua Users and Development List (www.eluaproject.net) <[hidden email]> Sent: Sunday, December 2, 2012 9:50 AM Subject: [eLua-dev] ARM9 Embedded PLC Hi Tom
I was thinking of using the LM3S6965. I think that it has ample resources to suit my requirements.
It comes with 64 KB of bit-banded SRAM and 256 KB of flash memory. It has the MAC and PHY built into the IC. All that one requires is the RJ45 connector. I think that this device was targeted for Ethernet to Serial bridges. There are detailed design and application notes on their website.
Without a doubt one cannot deny that ST has the lion's share of the Cortex market. I do use their devices regularly too. However there are certain niche markets that other vendors target.
Stellaris with their LM3S6965 for Ethernet
NXP and Energy Micro for Graphics Displays - EmWin is a free download for these devices.
Si-Labs have a highly configurable patented dual crossbar technology to define pinouts.
I guess it all boils down to what the end application is.
Regards
Quentin
That's OK, Quentin.
A new look at an existing product line is always welcomed.
Being that you are a hardware person, take a look at the W7200 in the Wiznet site.
Notice that it uses STM32 IP with 128K Flash and 20K RAM. If you can come up with the equivalent using Stellaris IP with 512 K Flash (or better) and 64K RAM (or better), I can use that.
On Sun, Dec 2, 2012 at 1:26 AM, Quentin Barry <[hidden email]> wrote:
Thanks for the link.
The issue here is that I am a hardware / embedded engineer. I don't want to buy someone else's solution - but want to design my own. You may call it re-inventing the wheel, but that is OK. I am planning on using one of the Luminary Micro / Stellaris Cortex M3 devices to implement the Ethernet to Serial bridge. I could simply have used a Tibbo module if I was so inclined.
I have taken a look at the Microchip offerings but then you are tied in to their compiler and development environment. With the Stellaris solution everything is open source. One also has the flexibility to change and add things as well. For example I could add a CC1125 to the Cortex as well and then I would have an Ethernet and an ISM band device in one.
Quentin
Take a look at:
On Thu, Nov 29, 2012 at 7:53 AM, Quentin Barry <[hidden email]> wrote:
That would be great. I also have quite a hectic schedule for approximately the next 2 weeks and then I will be free. Being your own boss can kill you sometimes.
I have all the PDF files for the PLC - where can I deposit them? If people are happy with what they see then I will upload all the Gerber files a bit later. All I need is a bit of guidance here on where to deposit the files without creating confusion. I guess a bit of moderator support is required at this junction.
Quentin.
I would be interested and willing to help you get eLua running on your PLC board. I am unlikely to have much time for the next two weeks due to a work project deliverable. After that I could spend some time on getting eLua running and working on some modules to interface to the various hardware peripherals.
I also may be interested in your Ethernet gateway board, as I have a few projects where I plan on using eLua and will need Ethernet.
-djd
On Nov 28, 2012, at 11:58 PM, Quentin Barry wrote:
Hello All
If I was to design an Ethernet to serial gateway would there be any interest? Basically it would accept 10/100 Mb Ethernet and convert it to serial or SPI and vica-versa.
I would make all the gerber files available. I think that a modular method is perhaps the best route to follow as main processor is then not burdened with these other tasks. All it has to do is to capture packets on the Serial or SPI layer, process them and reply if necessary.
I also have a complete design for a small PLC using the STR912FAW47. It has:
Most of the low level drivers are written in C and have been battled tested. This is revision 2 of the board, so there are a few hardware changes and some of the drivers have to change, or still have to be written. Everything is interrupt driven.
I have not yet had the time to implement eLua on it, but there is a port available for this CPU.
Is anyone interested in working with me to get this up and going with eLua?
Quentin_______________________________________________
eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev --
Douglas Davenport
_______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev -- Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private
infrastructure"
Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev -- Tom Freund Dig.y.SoL (TM) "Systems overseeing public and private
infrastructure"
Voice - 860-232-1614 Skype ID - digysol _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev _______________________________________________ eLua-dev mailing list [hidden email] https://lists.berlios.de/mailman/listinfo/elua-dev |
«
Return to eLua Development
|
1 view|%1 views
| Free forum by Nabble | Edit this page |